Вход на сайт
WIFI
1134
21.05.11 13:34
Выполнил инструкцию по установке драйвера для WIFI вот с этого сайта http://www.broadcom.com/support/802.11/linux_sta.php
Команда lsmod | grep wl выдает следующее
Я так понимаю, что драйвер загружен, но не совсем понятно что делать дальше. Никаких окон, сообщающих об обнаружении беспроводной сети не всплывает. Если кто разбирается в этом, проинструктируйте плз.
Команда lsmod | grep wl выдает следующее
В ответ на:
wl 2607564 0
lib80211 3278 2 lib80211_crypt_tkip,wl
wl 2607564 0
lib80211 3278 2 lib80211_crypt_tkip,wl
Я так понимаю, что драйвер загружен, но не совсем понятно что делать дальше. Никаких окон, сообщающих об обнаружении беспроводной сети не всплывает. Если кто разбирается в этом, проинструктируйте плз.
http://denis-aristov.ucoz.com
NEW 22.05.11 18:31
в ответ o_0 21.05.11 19:07
вот что выдает
а iwconfig выдает следующее:
В ответ на:
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
eth1 Failed to read scan data : Invalid argument
ppp0 Interface doesn't support scanning.
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
eth1 Failed to read scan data : Invalid argument
ppp0 Interface doesn't support scanning.
а iwconfig выдает следующее:
В ответ на:
lo no wireless extensions.
eth0 no wireless extensions.
eth1 IEEE 802.11abgn ESSID:""
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Bit Rate:270 Mb/s Tx-Power:24 dBm
Retry min limit:7 RTS thr:off Fragment thr:off
Power Managementmode:All packets received
Link Quality=5/5 Signal level=0 dBm Noise level=0 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
lo no wireless extensions.
eth0 no wireless extensions.
eth1 IEEE 802.11abgn ESSID:""
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Bit Rate:270 Mb/s Tx-Power:24 dBm
Retry min limit:7 RTS thr:off Fragment thr:off
Power Managementmode:All packets received
Link Quality=5/5 Signal level=0 dBm Noise level=0 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
http://denis-aristov.ucoz.com
NEW 22.06.11 10:47
в ответ kashej 22.05.11 18:31
а прежде чем самому компилить, не пробовал то, что в HOW TO INSTALL A PRE-COMPILED DRIVER написано? (там же в инструкции)
типа:
может уже до тебя все сделано, а ты зря мучаешься?
а в текущий момент можно было бы поставить WICD (apt-get install wicd),
запустить и в его настройках сказать, что влан это eth1.
типа:
В ответ на:
Ubuntu:
------
Go to System->Administration->Hardware Drivers
Choose the Broadcom STA wireless driver
Activate
Sometimes the driver does not show up in the Hardware Drivers choices. In
this case, try reintalling the driver from the GUI or shell like this:
From the GUI:
Package Manager (System>Administration>Synaptic Package Manager). Click the
Reload button in the upper left corner of Synaptic to refresh your index then
search for and reinstall the package named bcmwl-kernel-source.
From the shell:
sudo apt-get update
sudo apt-get --reinstall install bcmwl-kernel-source
In either GUI or text case, after reinstalling, reboot your machine.
Now go back to System->Administration->Hardware Drivers
and you should see the driver enabled and working.
Ubuntu:
------
Go to System->Administration->Hardware Drivers
Choose the Broadcom STA wireless driver
Activate
Sometimes the driver does not show up in the Hardware Drivers choices. In
this case, try reintalling the driver from the GUI or shell like this:
From the GUI:
Package Manager (System>Administration>Synaptic Package Manager). Click the
Reload button in the upper left corner of Synaptic to refresh your index then
search for and reinstall the package named bcmwl-kernel-source.
From the shell:
sudo apt-get update
sudo apt-get --reinstall install bcmwl-kernel-source
In either GUI or text case, after reinstalling, reboot your machine.
Now go back to System->Administration->Hardware Drivers
and you should see the driver enabled and working.
может уже до тебя все сделано, а ты зря мучаешься?
а в текущий момент можно было бы поставить WICD (apt-get install wicd),
запустить и в его настройках сказать, что влан это eth1.